Drum Pumps Malaysia | Finish Thompson (FTI) | Fluid Prowess

Drum pumps in Malaysia: Finish Thompson (FTI)

Tipping drums and using hand pumps is slow, messy and dangerous with chemicals. Finish Thompson (FTI) drum and barrel pumps transfer acids, solvents, oils and viscous liquids straight from drums, totes and tanks. As the master distributor of FTI pumps in Malaysia, Fluid Prowess helps you match the right tube, pump and motor to your liquid.

Electric drum pump on a blue drum in a chemical plant, drawing liquid up the suction tube and discharging it through a hose at the mouth of a container
Suction from the drum, discharge through a hose that reaches into the container to keep splashing to a minimum.

Why use a drum pump

Operator transferring chemical from a drum with a manual hand pump

Hand pump

Slow, tiring, and the operator works close to the chemical.

Finish Thompson (FTI) powered drum pump fitted to a chemical drum with discharge hose and nozzle

FTI drum pump

Fast, controlled transfer from the drum, with no tipping or pumping by hand.

Chemicals, oils and solvents usually arrive in 200-litre drums, IBC totes or carboys. Tipping a full drum risks spills, splashes and back injuries, and hand pumps are slow and tiring for anything more than a few litres.

A drum pump (also called a barrel pump) goes straight into the container through the bung opening. It transfers the liquid in minutes, with the operator standing clear, and then moves to the next drum.

How a drum pump works

A drum pump has three main parts: a motor, a pump tube and a discharge hose.

  1. Step 1: the tube goes into the drumThe pump tube is lowered through the bung opening at the top of the drum, towards the bottom of the container.MotorBung openingLower the tubeto near the bottom

    The tube goes into the drum

    The pump tube is lowered through the bung opening until it reaches near the bottom of the container.

  2. Step 2: the motor drives the pumpWith the discharge hose attached, the motor on top turns a shaft that runs down inside the tube to the impeller at the bottom.MotorMotor turnsthe shaftShaft runs downthe tubeImpeller atthe bottomHose attached

    The motor drives the pump

    The motor on top turns a shaft running down the tube to the impeller or pumping element at the bottom.

  3. Step 3: liquid rises up the tubeThe impeller at the bottom pushes liquid up through the tube to the discharge outlet near the top, where the hose is attached.MotorLiquid risesup the tubeDrawn in atthe bottomTo the discharge outlet

    Liquid rises up the tube

    The pumping element pushes liquid up through the tube to the discharge outlet at the top.

  4. Step 4: liquid flows out the hoseThe liquid flows through the discharge hose and nozzle into a receiving container. The pump can then be moved to the next drum.MotorOut through the hoseReceiving container

    Liquid flows out the hose

    The liquid leaves through the discharge hose and nozzle into the receiving container. Then the pump moves to the next drum.

What FTI drum pumps give you

Safer handling

No tipping or pouring, so less risk of spills, splashes and manual handling injuries.

Materials to match your chemical

Tubes in 316 stainless steel, PVDF, polypropylene, CPVC and pure polypropylene/PVDF.

Sealless options

Sealless series such as EF, PF and SF have no mechanical seal in the tube, improving reliability.

Thin to viscous liquids

From water-thin chemicals to high-viscosity products, with dedicated series for each.

A motor for every site

Splash-proof, enclosed, explosion-proof, air and lithium-ion battery motors, many with speed control.

FDA and ATEX options

Selected models, such as the PFS, offer FDA-compliant materials and ATEX certification.

Matching a drum pump to your liquid

The liquid decides the pump series, the materials and the motor. Start with how thick it is and whether it is flammable.

LiquidSuitable FTI series
Water, thin acids, caustic and hypochloriteEF, SF, PF (PP or PVDF), TB
Flammable solvents, thinners and fuelsStainless pumps only: EFS, SFS, PFS, TBS, TTS, BTS or HVDP, with an air or explosion-proof motor and a static protection kit
Up to about 1,000 cP (light oils, engine oil)EF (to 300 cP), TB (to 200 cP), SF, PF
1,000 to 2,000 cP (glycerin, detergent, paint)PF (electric) or TT (air)
2,000 to 15,000 cP (gear oil, resin, adhesive)BT
Above 15,000 cP (honey, syrup, silicone, pastes)HVDP, up to 100,000 cP
Food and beverageFDA versions: SFS-B, SFS-P, PFS-B, STTS, BT with FDA option, HVDP with Buna stator
Liquids that settle in the drumTM drum mixer first, then pump

Viscosity rises sharply when a liquid is cold, so check it at working temperature.

Finish Thompson drum and barrel pump series

Finish Thompson makes eight drum pump series, from thin acids to 100,000 cP pastes and from hand-pump replacements to explosion-proof solvent transfer. Start with viscosity: it decides which series can move your liquid.

SeriesShaft sealMax viscosityMax flowMax headBest for
EFSealless300 cP64 L/min6 mLight duty, hand-pump replacement, cordless 12 V
SFSealless1,200 cP140 L/min25 m (-H)One fixed daily job, hypochlorite, AdBlue, small bungs
PFSealless2,000 cP151 L/min24 mHeaviest duty, varied jobs, thicker liquids
TBSealed200 cP76 L/min8.5 mLow-cost stainless pump for thin solvents and mild chemicals
TTSealed2,000 cP (air), 50 cP (electric)61 L/min (air)9 m (air)Paints, inks, solvents on air drive; food (STTS)
BTSealed15,000 cP38 L/min61 mOils, resins, adhesives, glycerin, gear lube
HVDPMechanical seal100,000 cP32 L/min91 m (8 bar)Pastes, syrups, honey, silicone, polymers
TM (mixer)Sealed1,500 cP (air)53 L/min circulationNot applicableRe-mixing settled drums before pumping

Maximums with water unless stated. Flow and head fall as viscosity rises, except on BT, whose head rises with viscosity.

Finish Thompson PF Series sealless drum pump

PF Series

Sealless, maximum-performance pumps. One double-suction impeller gives both high flow and high head, and an adjustable orifice sets the flow. Built for varied duties, thicker liquids and heavy daily use.

Viscosity
Up to 2,000 cP with the M5TV motor (330 cP on an air motor)
Max flow
About 151 L/min; adjustable from 38 to 151 L/min
Max head
About 24 m
Full specifications
Pump type
Sealless centrifugal, double-suction impeller
Max temperature
49 to 104°C, depending on material
Tubes
51 mm; 27, 40, 48, 60 and 72 in; PP (PFM, PFP), PVDF (PFV) or 316 stainless steel (PFS)
Motors
M-series: M5V open, M5T/M5TV TEFC IP55, M5XV explosion-proof, M6 air
Flammable liquids
Yes, in 316 stainless steel (PFS) only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
FDA: PFS-B. ATEX: PFS-P with the M5XV motor
Finish Thompson SF Series sealless drum pump

SF Series

Sealless, high-performance pumps on a slim tube that fits smaller bung openings. Choose a high-flow or high-head (-H) impeller when ordering, for one regular duty.

Viscosity
About 1,000 to 1,200 cP, including on an air motor
Max flow
About 140 L/min (high flow) or 91 L/min (high head)
Max head
About 15 m (high flow) or 25 m (high head)
Full specifications
Pump type
Sealless centrifugal; high-flow or high-head (-H) impeller chosen at order
Max temperature
60 to 100°C, depending on material
Tubes
41 mm; 27, 40, 48, 54, 60 and 72 in; PP (SFM, SFP), PVDF/PP (SFV), PVDF (SFVV), 316 stainless steel (SFS), plus SFM-DEF for AdBlue
Motors
M-series: M5V open, M5T/M5TV TEFC IP55, M5XV explosion-proof, M6 air
Flammable liquids
Yes, in 316 stainless steel (SFS) only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
FDA: SFS-B and SFS-P
Finish Thompson EF Series economy drum pump

EF Series

Sealless economy pumps for occasional decanting of thin chemicals, and a budget replacement for hand pumps. A cordless battery motor works where there is no power point.

Viscosity
Up to 300 cP (100 cP on the battery motor)
Max flow
About 64 L/min
Max head
About 6 m
Full specifications
Pump type
Sealless, axial-flow impeller
Max temperature
66 to 100°C, depending on material
Tubes
32 mm; 16, 27, 40, 48 and 54 in; PP (EFP), PVDF/PP (EFV) or 316 stainless steel (EFS)
Motors
EF motors only: S1/S2 electric (2-speed), S4 air, S6 12 V cordless battery
Flammable liquids
Yes, in 316 stainless steel (EFS) only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
Not listed for EF; ask us
Finish Thompson TB Series stainless drum pump

TB Series

The lowest-cost stainless steel pump: a compact sealed pump for thin solvents, cleaners and mild chemicals.

Viscosity
Up to 200 cP
Max flow
About 76 L/min
Max head
About 8.5 m
Full specifications
Pump type
Compact sealed economy pump
Max temperature
66°C
Tubes
316 stainless steel (TBS), 38 mm, 40 in
Motors
The same M-series motors as SF and PF, including M6 air
Flammable liquids
Yes, as the stainless TBS only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
Not listed for TB; ask us
Finish Thompson TT Series screw-type drum pump

TT Series

Sealed pumps with a PTFE screw-type rotor for paints, inks and solvents. TT is mainly an air-driven pump: the air motor handles far thicker liquids than the electric motor.

Viscosity
Air motor: 1,500 cP (M6) to 2,000 cP (M6X). Electric motor: 50 cP
Max flow
About 61 L/min on air (38 L/min electric)
Max head
About 9 m on air (3 m electric)
Full specifications
Pump type
Sealed, PTFE screw-type rotor
Max temperature
66°C
Tubes
TTS: 316 stainless steel, 38 mm, 27/40/48 in. TTC: CPVC with Alloy 625, 40 in. STTS: FDA 316 stainless steel, 40 in
Motors
M8TV / M8XV electric (250 W) or M6 / M6X air
Flammable liquids
Yes, as the stainless TTS only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
FDA: STTS for food
Finish Thompson BT Series drum pump for viscous liquids

BT Series

Sealed stainless steel pumps with a PTFE screw-type rotor and heavy motors, for oils, resins, adhesives, gear lube and glycerin. Head rises as the liquid gets thicker. Not for thin, water-like liquids.

Viscosity
800 to 15,000 cP, depending on motor size
Max flow
About 38 L/min
Max head
About 61 m (rises with viscosity)
Full specifications
Pump type
Sealed, PTFE screw-type rotor
Max temperature
93°C
Tubes
316 stainless steel (BTS), 51 mm, 40 or 48 in; 1Â― in outlet
Motors
0.75 to 2.2 kW industrial induction (1- or 3-phase), explosion-proof, or large air motors (40 to 170 cfm)
Flammable liquids
Yes, as the stainless BTS only, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
FDA and tri-clamp option
Finish Thompson HVDP progressing cavity drum pump

HVDP Series

Progressing cavity (positive displacement) drum pumps for thick pastes such as honey, syrup, silicone, lotions and polymers, and for pushing through long lines at up to 8 bar. Never run it dry: the stator is damaged quickly.

Viscosity
Up to 20,000 cP (HR) or 100,000 cP (LR)
Max flow
About 32 L/min
Max head
About 91 m (8 bar)
Full specifications
Pump type
Progressing cavity, mechanical seal
Max temperature
82°C
Tubes
316 stainless steel, 51 mm, 27/40/48 in; Buna, FKM or PTFE stator; 1Â― or 2 in outlet
Motors
HR: 1 kW universal (M74/M76/M78). LR: 0.75 to 1.5 kW induction or air
Flammable liquids
Yes, with an air or explosion-proof motor and the static protection kit
FDA / ATEX
Buna stator for food (FDA)
Finish Thompson TM Series drum mixer

TM Series drum mixer

A 4-blade turbine drum mixer that pulls liquid in at the top and discharges it at the bottom, without a vortex or air, to resuspend settled solids in paints, dyes, inks, stains and solvents. It mixes; pair it with a pump.

Viscosity
Air motor: 1,000 to 1,500 cP. Electric motor: 100 cP
Circulation
About 53 L/min
Max head
Not applicable (mixer)
Full specifications
Type
Drum mixer, 4-blade turbine (not a pump)
Max temperature
93°C
Shaft
316 stainless steel (TMS), 51 mm, 40 in
Motors
M8TV / M8XV electric or M6 / M6X air
Flammable liquids
Ask us: not listed with FTI’s flammable-liquid series
FDA / ATEX
Not listed for TM; ask us

Sealless drum pumps: EF vs SF vs PF

Finish Thompson’s three sealless electric and air drum pumps cover everything from occasional decanting to heavy daily use. Here are the key differences at a glance.

FactorEF SeriesSF SeriesPF Series
Max flowAbout 64 L/minAbout 140 L/min (high flow), 91 L/min (high head)About 151 L/min
Max headAbout 6 mAbout 15 m (high flow), 25 m (high head)About 24 m
ImpellerOne fixed impellerHigh flow or high head, chosen at orderDouble-suction: high flow and high head
Max viscosity300 cP (100 cP on battery)About 1,000 to 1,200 cP, also on airUp to 2,000 cP (M5TV); 330 cP on air
Flow control2-speed motorMotor speed (variable-speed motors)Variable orifice 38 to 151 L/min, plus motor speed
Tube diameter32 mm41 mm; fits smaller bungs51 mm
DischargeÂū in hose barb1 in hose barb, radial O-ring swivel1 in hose barb, O-ring swivel
Built-in strainerYesYes on high flow; no on -HNo; optional add-on
MotorsS1/S2 electric, S4 air, S6 12 V batteryM5V, M5T/M5TV, M5XV Ex-proof, M6 airSame M-series motors as SF
Price levelLowestMidHighest

Choose EF whenâ€Ķ

  • You decant thin chemicals occasionally
  • You’re replacing a hand pump on a budget
  • There’s no power point: use the S6 cordless battery motor

Choose SF whenâ€Ķ

  • You have one regular job: emptying IBCs, or pumping up to a tank (-H)
  • Bung openings are small, or you pump hypochlorite or AdBlue
  • Price matters, but you still need performance

Choose PF whenâ€Ķ

  • Duties vary, and you need high flow and high head from one pump
  • Liquids are thicker, up to 2,000 cP
  • The pump sees heavy daily use, and you want adjustable flow

Performance figures are approximate maximums measured with 1.5 m of hose; actual duty depends on the liquid, motor and hose. Viscosity limits depend on the motor selected. A 40 in tube suits 200 L drums, and a 48 in tube suits 1,000 L IBCs.

Motors and safety with flammable liquids

Finish Thompson offers splash-proof/open drip-proof motors (IP24), enclosed TEFC motors (IP54/55), explosion-proof motors (IP54/55), air motors and lithium-ion battery motors (IP24). Many come with speed control for more precise filling. For Malaysia, we supply motors for 230 V or 415 V, 50 Hz power.

Pumping flammables or combustibles needs the right setup. Finish Thompson specifies explosion-proof electric or air motors on stainless steel tubes, with a static protection kit. That means a stainless pump (EFS, SFS, PFS, TBS, TTS, BTS or HVDP), never a plastic pump or a standard motor. Some series don’t offer options for flammables at all, so tell us what you’re pumping and we’ll make sure the whole pump suits it.

Drum pump applications and industries

Anywhere liquids arrive in drums, totes or carboys, a drum pump makes transfer faster and safer.

  • Chemical distribution & blending: decanting acids, bases and solvents
  • Water treatment: refilling dosing tanks with treatment chemicals
  • Electroplating & metal finishing: transferring plating and cleaning chemicals
  • Laboratories & electronics: handling high-purity and corrosive chemicals
  • Food & beverage: syrups, flavours and ingredients, with FDA-compliant options
  • Automotive & workshops: oils, coolants and diesel exhaust fluid (DEF)
  • Paints, coatings & inks: transferring and mixing viscous products
  • Manufacturing plants: lubricants, detergents and process chemicals

When you need more than a drum pump

Drum pumps are made for portable transfer from containers. For fixed chemical transfer lines, a magnetic drive pump is a better fit. For thick sludges in larger volumes, consider a rotary lobe pump, and for continuous chemical dosing, Wanner Hydra-Cell metering pumps.

Why buy FTI drum pumps from Fluid Prowess

Fluid Prowess is the master distributor of Finish Thompson (FTI) pumps in Malaysia. We bring FTI pumps, spare parts and accessories into Malaysia through Finish Thompson’s official channel, and act as the local link between your plant and the manufacturer.

We are also a one-stop pump solution provider, so we can look at the whole job, not just the drum pump.

  • The official source in Malaysia: every FTI pump comes through Finish Thompson’s authorised channel, so you know it’s genuine, built to current specifications and backed by warranty support handled locally.
  • Direct line to the manufacturer: for unusual chemicals, special configurations or technical questions, we work directly with Finish Thompson to get you a reliable answer.
  • The full FTI range, not just what’s on the shelf: any series, tube material, tube length, motor and accessory can be ordered through us, including FDA, ATEX and flammable-liquid configurations.
  • Genuine spare parts that fit: replacement motors, tubes, impellers, seals and hoses made for your pump, so you avoid look-alike parts that don’t couple properly or don’t suit your chemical.
  • Chemical compatibility checks: tell us the liquid, concentration and temperature, and we’ll confirm every wetted part suits it, not just the tube.
  • Safe setups for flammables: we specify the explosion-proof or air motor, stainless steel tube and static protection kit Finish Thompson requires for flammable and combustible liquids.
  • The right fit for your containers: we match the tube length and accessories to your drums, IBC totes or tanks.
  • Local support and pricing: quotations in ringgit, one point of contact in Malaysia, and no need to import pumps or parts yourself.

Frequently asked questions

What is a drum pump?

A drum pump, also called a barrel pump, is a portable pump with a long tube that goes into a drum, tote or tank through the bung opening. A motor on top drives an impeller or pumping element at the bottom of the tube, lifting the liquid out through a discharge hose without tipping the container.

What is the difference between a sealless and a sealed drum pump?

Sealless drum pumps have no mechanical seal in the tube, which improves reliability with thin, corrosive liquids. Sealed drum pumps use a seal and suit a wider range of liquids, including higher-viscosity products, depending on the series.

Can a drum pump transfer flammable liquids?

Yes, with the right configuration. Use a stainless pump (EFS, SFS, PFS, TBS, TTS, BTS or HVDP) with an air or explosion-proof motor and a static protection kit. A plastic pump or a standard motor can start a fire.

Which drum pump is best for viscous liquids?

It depends how thick it is. PF handles up to 2,000 cP and TT up to 2,000 cP on an air motor. BT covers 2,000 to 15,000 cP, such as gear oil, resins and adhesives. Above 15,000 cP, or when you need pressure to push through long lines, choose the HVDP, which handles up to 100,000 cP.

What drum pump tube length do I need?

Choose a tube that reaches near the bottom of your container. As a guide, a 40 in tube suits a standard 200 L drum, and a 48 in tube suits a 1,000 L IBC. EF, SF and PF tubes come in lengths from 16 in to 72 in, depending on the series.

Can a drum pump run dry?

No. Finish Thompson’s manuals say never to run the pump dry, and never against a closed valve for more than a minute. The liquid cools and lubricates the bearings, and on the HVDP the stator. Switch off as soon as the container is empty.

Where can I buy FTI drum pumps in Malaysia?

Fluid Prowess is the master distributor of Finish Thompson (FTI) pumps in Malaysia, supplying drum and barrel pumps, motors, spare parts and accessories, with selection support. Contact us with your liquid and container size.

Tell us what you need to transfer

Share the liquid, its concentration and temperature, the container size and whether it’s flammable. We’ll recommend the right FTI drum pump, tube and motor.