Centrifugal pumps in Malaysia

Centrifugal pumps are the most widely used pumps in industry, moving water, chemicals, oils and process liquids in almost every plant. Fluid Prowess supplies centrifugal pumps from Kewpump, M Pumps and Finish Thompson, and helps you choose the right type for your liquid and duty.

How a centrifugal pump works Liquid enters through the suction inlet at the centre of the impeller. The spinning impeller vanes throw it outwards by centrifugal force into the spiral volute casing, which widens towards the discharge outlet, where the pressurised liquid leaves. Water in Suction inlet (impeller eye) Discharge outlet Volute casing widens towards the outlet, building pressure Impeller vanes throw liquid outwards Rotation
Simplified end-suction centrifugal pump, viewed from the suction side.

How a centrifugal pump works

A centrifugal pump turns the motor’s energy into flow and pressure with a spinning impeller.

  1. Liquid enters the eye

    Liquid flows in through the suction, into the centre (eye) of the impeller.

  2. The impeller spins it outwards

    The rotating vanes throw the liquid outwards at high speed.

  3. The volute builds pressure

    The spiral casing slows the liquid down, turning its speed into pressure.

  4. Liquid leaves the discharge

    Pressurised liquid exits through the discharge into the pipework.

Types of centrifugal pumps

All centrifugal pumps share the same principle, but each type is built for a different kind of duty.

End-suction process pumps

The workhorse design for water, chemicals and process liquids, often built to ISO 2858, ISO 5199 or ANSI dimensions.

Magnetic drive pumps

Seal-less pumps driven through a magnetic coupling, for hazardous liquids that must not leak.

Canned motor pumps

Seal-less pumps with the motor and pump in one sealed unit.

Plastic and plastic-lined pumps

PP, PVDF, PFA or ETFE construction for strong acids and alkalis.

Solids handling pumps

Non-clogging impellers for liquids carrying suspended solids or fibres.

Self-priming pumps

Lift liquid from below the pump without a flooded suction.

Vertical and sump pumps

Motor above the liquid, for pits, sumps and tanks.

Thermal oil pumps

Built to circulate hot heat transfer oils.

Mixed flow pumps

For large volumes at lower heads.

Side channel and regenerative pumps

For low flows at high heads.

Sealed or seal-less?

The biggest choice after pump type is how the shaft is sealed.

FactorMechanical sealMagnetic drive (seal-less)Canned motor (seal-less)
Leak path at the shaftYes; the seal wears over timeNoneNone
Best forWater and non-hazardous liquids, liquids with solidsHazardous, toxic and corrosive chemicalsHazardous liquids where space is tight
MotorStandard motorStandard motorSpecial integrated motor
Learn moreKewpumpM Pumps, FTIAsk us

Centrifugal pump ranges we supply

Choose a range to see the full details, specifications and models.

Process, solids handling and thermal oil pumps

KEWPUMP · MALAYSIA

Stainless steel end-suction centrifugal pumps, made in Malaysia since 1988.

â€Ē KS-SG2 chemical process (ISO 2858 / ISO 5199)
â€Ē KS-SR general application
â€Ē KS-SE2 and KS-SE3 solids handling
â€Ē KS-TO thermal oil, KS-MF mixed flow, FM/KS small pumps
â€Ē KS-VSP vertical sump and OSP oil skimmer

Magnetic drive pumps

M PUMPS · ITALY

Seal-less magnetic drive pumps with fully encapsulated magnets, for hazardous and corrosive liquids.

â€Ē ISO and ANSI process pumps
â€Ē API 685 pumps for oil and gas
â€Ē Side channel and regenerative pumps
â€Ē Plastic and PFA-lined versions

Plastic and plastic-lined chemical pumps

M PUMPS · FTI · DJ PUMP · WANNER

Pumps where the liquid only touches plastic, for strong acids, alkalis and high-purity chemicals.

â€Ē PP and PVDF plastic pumps
â€Ē PFA and ETFE-lined pumps
â€Ē How to choose between plastic and lined

Drum and barrel pumps

FINISH THOMPSON (FTI) · USA

Portable pumps for transferring chemicals, oils and solvents from drums, IBCs and tanks. Fluid Prowess is FTI’s master distributor in Malaysia.

â€Ē Sealless and sealed drum pumps
â€Ē Electric, air and battery motors
â€Ē Options for flammable liquids

Canned motor pumps

ASK US

Compact seal-less pumps with the motor and pump in one sealed unit, for hazardous liquids.

â€Ē No shaft seal and no coupling
â€Ē Compare with magnetic drive on our M Pumps page

How to choose a centrifugal pump

Send us these details and we’ll recommend the right type, brand and materials:

  • The liquid: what it is, its concentration, and whether it is hazardous
  • Flow and head: how much you need to move, and how far or high
  • Temperature: normal and maximum
  • Solids: size and amount, if any
  • Viscosity: thicker liquids may need a positive displacement pump instead
  • Installation: suction conditions, space, and hazardous area classification

Frequently asked questions

What is a centrifugal pump?

A centrifugal pump uses a spinning impeller to throw liquid outwards into a volute casing, which turns that speed into flow and pressure. It is the most widely used pump type for water and thin liquids.

What is the difference between a sealed and a seal-less centrifugal pump?

A sealed centrifugal pump has a mechanical seal or packing where the shaft enters the casing, which can wear and leak. A seal-less pump, such as a magnetic drive or canned motor pump, has no shaft passing through to the liquid, so there is no seal to leak. Seal-less pumps are used for hazardous, toxic or expensive liquids.

Which centrifugal pump is best for chemicals?

For corrosive or hazardous chemicals, a seal-less magnetic drive pump is usually the safest choice. Metal mag drive pumps suit most process chemicals, while plastic or plastic-lined mag drive pumps suit strong acids and alkalis. For less hazardous chemicals, a stainless steel chemical process pump such as the Kewpump KS-SG2 is an economical option.

When should I not use a centrifugal pump?

Centrifugal pumps lose efficiency with very viscous liquids and are not designed for accurate dosing or very high pressure at low flow. For those duties, a positive displacement pump such as a screw, lobe or diaphragm pump is usually a better choice.

Where can I buy centrifugal pumps in Malaysia?

Fluid Prowess supplies centrifugal pumps in Malaysia from Kewpump, M Pumps and Finish Thompson (FTI), including process, solids handling, thermal oil, magnetic drive, plastic and plastic-lined pumps, with selection, installation and maintenance support. Contact us with your duty.

Tell us about your pumping duty

Share your liquid, flow, head and temperature. We’ll recommend the right centrifugal pump, or another pump type if it suits you better.